Baldor 15P Series Spécifications

Series 15PInverter Control8/02 MN715PInstallation and Operating Manual

MN715P Receiving and Installation 3-4AC Line ConnectionsA power disconnect should be installed between the input power service andthe control for a f

3-5 Receiving and Installation MN715PThree Phase Wire Size and Protection DevicesTable 3-3 Wire Size and Protection Devices - 3 phaseControl Control

MN715P Receiving and Installation 3-6115VAC 1 Phase Wire Size and Protection DevicesTable 3-4 Wire Size and Protection Devices - 1 phaseControlInput

3-7 Receiving and Installation MN715P230VAC Single Phase Derating for Three Phase ControlsSingle phase AC input power can be used to power a three pha

MN715P Receiving and Installation 3-8Motor Brake ConnectionsFor motors with spring set brakes, connect the brake power leads and themotor power leads

3-9 Receiving and Installation MN715PAnalog Input(S1-7 = OFF)If S1-7 is OFF, the front panel % Speed potentiometer is selected. The J4inputs are igno

MN715P Receiving and Installation 3-10Digital Inputs(S1-8 = OFF)If S1-8 is OFF, the front panel commands FWD, REV and STOP are selected.The J4 inputs

Section 4Setup and Operation4-1 Setup and Operation MN715POverview The operator interface panel is shown in Figure 4-1.Figure 4-1 Operator Interface

MN715P Setup and Operation 4-2S1 Settings (OFF = Open; ON = Closed) S12X Base1X Base50 Hz60 HzREV DisabledREV EnabledAutoManual3 Wire2 Wire4Ć20mA C

4-3 Setup and Operation MN715PS1 Settings ContinuedSwitchSetting DescriptionOFF Base Frequency = 60Hz1ON Base Frequency = 50HzOFF Maximum frequency li

Table of ContentsMN715P Table of Contents iSection 1Quick Start 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MN715P Setup and Operation 4-4Potentiometers P1 - P6 (270° of rotation)Refer to Figure 4-1 for location of potentiometers.ACCEL time – P1The time re

4-5 Setup and Operation MN715POperation ExamplesOperating the Control from the Front PanelTo place the control in local speed and command mode, place

MN715P Setup and Operation 4-6Figure 4-3 Remote 0-10VDC 3 Wire OperationJ4123456ReverseStopSpeed CommandForwardNot usedGNDS1 Pos. Description5 ON 3

Section 5Troubleshooting5-1 Troubleshooting MN715PThe Baldor Series 15P Control requires very little maintenance, if any, andshould provide years of t

MN715P Troubleshooting 5-2Fault Code 1 – Non Resettable hardware fault (Power LED is blinking).May indicate a HW Surge Current, HW Protect or a Power

5-3 Troubleshooting MN715PFault Code 3 – Bus faults. May indicate an Over-voltage, Under-voltage orPrecharge fault was detected.Power LED Fault LED A

Section 6Specifications and Product DataMN715P Specifications and Product Data 6-1Specifications:Horsepower 0.33-1HP @ 115VAC1-5 HP @ 230VAC1-5 HP @

6-2 Specifications and Product Data MN715PDisplay:Control Specifications:Control Method Sine wave Carrier input, PWM outputPWM Frequency Rated @ 7.5kH

MN715P Specifications and Product Data 6-3Ratings Series 15P Stock ProductsRated RatedOutput CurrentCatalog No.RatedInputVoltsRatedOutputVoltsHP kWCo

6-4 Specifications and Product Data MN715PMounting Dimensions 4.396(112)7.210(183)7.654(195)4.886(124)POWER FAULTFWDREVSTOP0102030405060708090100% Sp

Section 1Quick Start1-1 Quick Start MN715POverviewThe quick start procedure is as follows:1. Read the Safety Notice and Precautions in section 2 of th

BALDOR ELECTRIC COMPANYP.O. Box 2400Fort Smith, AR 72902–2400(479) 646–4711Fax (479) 648–5792 Baldor Electric Company Printed in USAMN715P 8/02 C&a

MN715P Quick Start 1-2Figure 1-1 Factory SettingsS12X Base1X Base50 Hz60 HzREV DisabledREV EnabledAutoManual3 Wire2 Wire4Ć20mA Current0Ć10V VoltageRe

Section 2General Information2-1 General Information MN715PCE ComplianceA custom unit may be required, contact Baldor. Compliance to Directive89/336/E

MN715P General Information 2-2 WARNING: Do not use motor overload relays with an automatic reset feature.These are dangerous since the process may in

Section 3Receiving and Installation3-1 Receiving and Installation MN715PReceiving & InspectionThe Series 15P Inverter control is thoroughly tested

MN715P Receiving and Installation 3-2Control InstallationThe control must be securely fastened to the mounting surface. Use the four(4) mounting hol

3-3 Receiving and Installation MN715PCover RemovalThe cover is made of plastic and could be damaged during removal if handledroughly. Refer to Figure